Can i deck over grass

Measure out the area you want your deck to cover this should be in your design plan and hammer a peg into each of the corners of your deck. Make sure the ground is level, you can do this by checking your site with a straightedge and a spirit level.

Remove the turf until the ground is completely even. Cover the area of your site with a layer of weed control fabric to prevent any weed regrowth coming up under your decking.

Use a pencil to measure and mark the deck board at the desired length, then use a combination square to draw the line across the deck board. Make two pencil marks where the two outer joists meet the inner joists at the right angle. This is where the coach screws will go. Use a flat wood bit to drill recesses into each of the eight marks you have just made making sure the screw heads will be flush with the joint surface when done. Drill a hole through the center of each recess from the outer joist to the adjoining outer joist.

That should be your outer frame assembled and now you can move onto securing the inner joists. This is done by securing two coach screws through the outer frame into the inner joists. Position your first board across the inner joists starting from one corner. Make sure that the deck board is in the opposite direction to the inner joists and flush to the frame.

Mark a cutting line for the end of the first board and cut it to fit making sure you allow an expansion gap of 3mm in your measurements. This is done by screwing every deck board to every joist that it covers over along the frame. Use two decking screws where each bard meets a joist. Use a sander to smooth over any cut ends and apply an end grain preserver to protect the timber from rot and decay.

Gone are the days when garden fences were simply a privacy barrier between your garden and the next Quirky As homeowners, we take pride in preserving our gardens Levelling a garden can end up being a hefty job, but trust us wh This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.

Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings. If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.

Do we deliver to your area? Check here. Checking postcode Step 3: Cut and lay your joists. Step 4: Re-bury those deck piers. Step 5: Prep your deck wood. Step 6: Waterproof the bottom of your deck planks. Step 7: Lay your decking planks. Step 8: Add end-caps. Can you build a deck over grass? Category: hobbies and interests card games. What do you put under decking? Weed Control. Should decking be laid level?

How high should decking be off the ground? Is decking cheaper than paving? Do you need foundations for decking? Ground-Level Deck Foundations. Do you need a permit to build a deck on the ground? What happens if you don't get a building permit for a deck? How do you prepare the ground under a deck? Preparing Deck Site Checklist.

Layout the shape of the deck with a hose or string and remove any sod. How much does a 20x20 deck cost? How many footings do I need for a deck? What size deck needs council approval? Will pressure treated wood rot in ground? Pressure - Treated Wood Makes the Grade. Can I use deck pier blocks instead of footings? Ignoring this step can damage your deck.

Next, dig down approximately 50 mm. Make sure to remove any leftover turf. Make sure that the ground is even. You can use a tamper to flatten the ground. You may need to move soil around to flatter the area. Next, cover the area with a weed control landscaping fabric. This fabric helps prevent any grass growth, which can damage your deck. After laying the fabric, cover the area with 40 mm to 50 mm of gravel. Gravel offers protection against water and moisture buildup.

Other excellent alternatives are wood chips and stone pebbles. After finishing the foundation, start measuring and cutting your boards. You can use a pencil to mark the desired lengths. A combination square is also a handy tool to be able to create lines across the boards. As much as possible, double-check for accuracy. Next, you may want to lay down all the materials on the desired area. Doing this will help you determine whether you have enough materials for the job.

You will also need to put gaps between the boards for a more accurate layout. If you haven't already, this is the last chance to make changes to your design and layout.